Air-suspension D2R-CONV D2-AS-CS-S LS Manuel d'utilisateur télécharger pdf

DETAIL A

SCALE 1 : 5

UPPER ISOLATOR

TIGHTER

COILS UP

COIL

SPRING

10MM BOLTS

LOWER SPRING

SEAT

FRACTIONAL

NAME

DATE

DRAWN

KMD

11/08/07

CHECKED

ENG APPR.

DICO VERY 2

REAR SUSPENSION /

COIL SPRING - SLS MANUAL

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

ARNOTT, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

ARNOTT, INC. IS

PROHIBITED.

MFG APPR.

MATERIAL

Q.A.

COMMENTS:

USED ON

FINISH

NEXT ASSY

DWG. NO.

D2-AS-CS-S LS

SIZE

REV.

APPLICATION

DO NOT SCALE DRAWING

SCALE:1 :16

SH E E T 1 OF 1

WEIGHT:

REAR -- AIR SPRING ASSEMBLY

Remove

WARNING: The air suspension system can be pressurized

up to

10 bar (150 lbf/in²). It’s always important to make sure that dirt or

grease

doesn’t enter system. Always wear hand, ear and eye protection when

servicing

the air suspension system.

WARNING: Do not inflate the air spring assembly unless it

is supported on both ends by the vehicle frame and suspension system.

Failure to observe this warning may result in serious injury and

damage to the air springs assembly. YOU SHOULD NEVER

ATTEMPT TO DISMANTLE THE AIR SPRINGS.

1. Raise the vehicle on a hoist or other adequate structure. WARNING:

Always support the vehicle on safety stands. Refer to your

owner’s manual for correct lifting instructions. Remove road

wheel.

2. Disconnect the pipe from top of air spring. Removing the air fitting

will depressurize the air spring.

3. Seal off hose to prevent dirt or grease from entering system.

4. Remove the 2 clips securing the top of the air spring to chassis.

5. Collapse the air spring.

6. Rotate the air spring to unlock it from axle, and remove the old air

spring from the vehicle.

7. Remove the old air connector from the pipe.

CAUTION: When refitting the new air spring, do not allow the

vehicle to rest on the deflated air spring. The chassis must be

supported until the new air spring is inflated.

Refit

1. Locate the two holes for the spring seat retaining bolts. Run a

10mm x 1.50 tap thru these holes to ease installation of retaining

bolts.

2. Install lower spring seats onto axle.

3. Jack up axle to release tension from shock absorber. Remove lower

shock bolt. Release ABS sensor lead from bracket.

4. Install upper spring isolator to top of spring. Note: top has the

tighter coils at top.

5. Lower axle until the spring can be installed in place.

6. Raise axle making sure spring stays aligned in place. Reinstall the

shock bolt and clip ABS sensor lead in place.

7. Repeat for opposite side.

8. Reprogram slabs computer to coil springs using Autologic or Test

Book diagnostic system (this will disable the air suspension

system.)

9. Road test for unusual noises.

SH E E T 1 OF 1 1
WEIGHT: 1

Résumé du contenu

Page 1 - WEIGHT:

4 DETAIL A SCALE 1 : 5 A UPPER ISOLATOR TIGHTER COILS UP COIL SPRING 10MM BOLTS LOWER SPRING SEAT FRACTIONAL NAME DATE DRAWN KMD 11/08/07 CHECKED EN

Commentaires sur ces manuels

Pas de commentaire

Air-suspension D2R-CONV D2-AS-CS-S LS Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Air-suspension D2R-CONV D2-AS-CS-S LS. Air Suspension D2R-CONV D2-AS-CS-S LS User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Air-suspension D2R-CONV D2-AS-CS-S LS